Practice Free NS0-184 Exam Online Questions
Which two functions does the management network provide? (Choose two.)
- A . to provide access to the system console of any node in the cluster
- B . to collect diag log files
- C . to replicate the cluster configuration to all nodes
- D . to transfer SVMs between the cluster nodes
You are a NetApp Professional Services engineer, employed by NetApp. You have just completed an ONTAP cluster installation. You need to collect the relevant configuration information to enable the Service Event Report (SER) to be created.
Which tool would you use to accomplish this task?
- A . Active IQ scheduled reports
- B . NetAppDocs output report
- C . ONTAP System Manager
- D . Active IQ Config Advisor worksheet
You are asked to install a 14-node cluster with FAS8020 controllers. The customer decided that he only wants to use two ports per controller for cluster interconnects.
According to NetApp best practices, which switch should be used for the cluster interconnect?
- A . Brocade 6510
- B . Cisco 5596
- C . NetApp CN1610
- D . NetApp CN1601
After an initial setup, you want to create a new data aggregate. The node has thirty-one 4 TB SATA spare disks assigned. Your customer wants to have two spare disks.
In this scenario, which two settings would you use to reach the maximum capacity and availability? (Choose two.)
- A . -maxraidsize 31
- B . -raidtype raid_tec
- C . -raidtype raid_dp
- D . -maxraidsize 29
Exhibit:
You are installing a new FAS cluster. The management network must be on tagged VLAN 11 for remote administration by a service provider.
Referring to the exhibit, which two ports will allow service provider access to both cluster and node management LIFs? (Choose two.)
- A . e0a-11
- B . e0M
- C . e0M-11
- D . e0b-11
You have just installed a new FAS2620 on a cluster site. You are using the USB cable for the intial configuration.
In this scenario, what is the default speed for the serial connection?
- A . 9600 bps
- B . 15200 bps
- C . 576000 bps
- D . 115200 bps
A customer wants you to add a disk shelf that contains SSDs so they can implement Flash Pool.
Which three tools would you use to complete this task? (Choose three.)
- A . Use the My AutoSupport tool to ensure that Flash pool is licensed.
- B . Use Hardware Universe to ensure that you would not exceed the maximum drive count.
- C . Use Hardware Universe to ensure that you would not exceed the maximum cache for the system.
- D . Use the My AutoSupport tool to see if there is a Flash Cache card installed.
- E . Use Config Builder to verify the shelves can be added.
On a new installation, you have identified that the components required to perform the task are not all functional. One of the controllers in the cluster fails to see any disks and cannot join the cluster.
Which response to the customer indicates that you are in control of the situation?
- A . “A failed component has been identified. I will reschedule when you receive the new part.”
- B . “A failed component has been identified. It will stop the installation for now.”
- C . “A failed component has been identified. What do you want me to do about it?”
- D . “A failed component has been identified. I have contacted support and here are your options…”
You are installing a 2-node clustered Data ONTAP system that has been shipped to the site in multiple boxes.
How do you find the disk shelves that contain the root volumes for each node?
- A . The box for the shelf containing the root volume is yellow.
- B . The box for the shelf containing the root volume is red.
- C . The root volume is on the nodes, not the disk shelves.
- D . The disk shelf’s sticker contains the controller’s serial number.
You are dispatched to install a new cluster with six AFF A300 nodes. While running Config Advisor, you determine that there is a newer firmware version for 48 SSDs.
Which statement is correct in this scenario?
- A . Prior to leaving the site, tell the customer that a later firmware exists for those disk drives, but that the upgrade will provoke downtime.
- B . Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.
- C . Unless the customer advises otherwise, upgrade the firmware on the SSDs to clear the Config Advisor error.
- D . Prior to leaving the site, advise the customer that the firmware is included in the version of ONTAP that they downloaded.